sonic-buildimage/dockers/docker-snmp-sv2/snmpd.conf.j2

###############################################################################
# Managed by sonic-config-engine
###############################################################################
#
# EXAMPLE.conf:
#   An example configuration file for configuring the Net-SNMP agent ('snmpd')
#   See the 'snmpd.conf(5)' man page for details
#
#  Some entries are deliberately commented out, and will need to be explicitly activated
#
###############################################################################
#
#  AGENT BEHAVIOUR
#

#  Listen for connections on all ip addresses, including eth0, ipv4 lo
agentAddress udp:161
# TODO: only support ipv4 lo addresses, add ipv6 support later

###############################################################################
#
#  ACCESS CONTROL
#

                                                 #  system + hrSystem groups only
view   systemonly  included   .1.3.6.1.2.1.1
view   systemonly  included   .1.3.6.1.2.1.25.1

                                                 #  Default access to basic system info
{% if snmp_rocommunities %}
{% for community in snmp_rocommunities %}
rocommunity {{ community }}
{% endfor %}
{% else %}
rocommunity {{ snmp_rocommunity }}
{% endif %}

###############################################################################
#
#  SYSTEM INFORMATION
#

#  Note that setting these values here, results in the corresponding MIB objects being 'read-only'
#  See snmpd.conf(5) for more details
sysLocation    {{ snmp_location }}
sysContact     Azure Cloud Switch vteam <linuxnetdev@microsoft.com>
                                                 # Application + End-to-End layers
sysServices    72


#
#  Process Monitoring
#
# todo: should we enable snmp based monitoring of sswsyncd and other processes?

# At least one 'sendmail' process, but no more than 10
#proc  sendmail 10 1

#  Walk the UCD-SNMP-MIB::prTable to see the resulting output
#  Note that this table will be empty if there are no "proc" entries in the snmpd.conf file


#
#  Disk Monitoring
#
                               # 10MBs required on root disk, 5% free on /var, 10% free on all other disks
disk       /     10000
disk       /var  5%
includeAllDisks  10%

#  Walk the UCD-SNMP-MIB::dskTable to see the resulting output
#  Note that this table will be empty if there are no "disk" entries in the snmpd.conf file


#
#  System Load
#
                               # Unacceptable 1-, 5-, and 15-minute load averages
load   12 10 5

#  Walk the UCD-SNMP-MIB::laTable to see the resulting output
#  Note that this table *will* be populated, even without a "load" entry in the snmpd.conf file



###############################################################################
#
#  ACTIVE MONITORING
#
# Note: disabled snmp traps due to side effect of causing snmpd to listen on all ports (0.0.0.0)
#
#   send SNMPv1  traps
#trapsink     localhost public
#   send SNMPv2c traps
#trap2sink    localhost public
#   send SNMPv2c INFORMs
#informsink   localhost public

#  Note that you typically only want *one* of these three lines
#  Uncommenting two (or all three) will result in multiple copies of each notification.


#
#  Event MIB - automatically generate alerts
#
# Remember to activate the 'createUser' lines above
#iquerySecName   internalUser
#rouser          internalUser
# generate traps on UCD error conditions
#defaultMonitors          yes
#note, this release of snmpd does not support linkUpDownNotifications
# generate traps on linkUp/Down
#linkUpDownNotifications  yes


#
#  AgentX Sub-agents
#
                                           #  Run as an AgentX master agent
master          agentx

#
#  SysDescription pass-through
#

pass -p 10 .1.3.6.1.2.1.1.1 /usr/share/snmp/sysDescr_pass.py